1 / 2Standard checkout available. Verified maker dispatch.
The Radiolink CrossFlight is a flight controller for aerial photography, FPV racing and general flying. The page describes advanced gyroscopic sensors and refined flight algorithms for accurate manoeuvres in a compact design.
It uses an HC32F4A0PITB processor with an ICM42670 gyro, VCM5883 compass and LPS22HB barometer, 10 PWM channels, 2 Mavlink UARTs (without CTS/RTS) and a Type-C USB port. RC input is PPM or SBUS and the OSD is integrated. It measures 39.7 x 39.7 x 13 mm and the controller alone weighs 16.5 g. The page showed it in stock at Rs 5,079 (SKU RS6047).
HC32F4A0PITB processor: as listed.
ICM42670 gyro, VCM5883 compass, LPS22HB barometer: the listed sensors.
10 PWM outputs: for motors and servos.
Integrated OSD: as listed.
Type-C USB port: 1 port.
Power module included: 2-12S.
A flight controller is the brain of a multirotor or fixed-wing aircraft. It reads the gyroscope, and where fitted the accelerometer, barometer and compass, and runs a control loop that compares what the aircraft is doing with what the pilot asks for. It then sends new speed commands to the motors through the ESCs or servos many times each second. A faster processor and a better gyro allow a higher loop rate and a more locked-in feel.
Wiring and firmware decide what the board can do. The number of UARTs limits how many receivers, GPS units, telemetry radios and video systems you can connect, the PWM or motor outputs limit how many motors and servos it can drive, and the input voltage range must suit your battery and power module. Before you buy, check that the firmware you want to run supports the board and that its mounting pattern fits your frame.
Set up carefully. Flash a firmware that is listed as supported, configure the receiver protocol, set the motor order and direction, calibrate the accelerometer and, for larger aircraft, the compass, and always test with the propellers removed first. Keep the board isolated from vibration with soft mounts where the design calls for them, and never power it with a supply that is outside the rated input voltage.
Keep the aircraft safe. Confirm your failsafe settings and arming switch before the first flight, keep a backup of your configuration, and update firmware only when you have a reason to. A flight controller is a safety-critical part, so use the wiring diagram from the maker and avoid guesswork with power connections.
Aerial photography
FPV racing
3-8 copters
Airplanes and helicopters
Cars and boats
The page lists adaptable models as 3-8 copter, airplane, helicopter, car and boat. The operating temperature is -40 to 80°C.
The package includes a power module (2-12S), buzzer, I2C transfer board, status LED, 4 GB MicroSD card, cables, adhesive tape, a Type-C cable and a manual.
Processor: HC32F4A0PITB
Gyro: ICM42670
Compass: VCM5883
Barometer: LPS22HB
PWM output: 10 channels
Mavlink UART: 2 (without CTS/RTS)
USB port: 1 (Type-C)
RC signal input: PPM/SBUS
OSD: integrated
Operating temperature: -40 to 80°C
Dimensions: 39.7 x 39.7 x 13 mm
Weight: 16.5 g (controller only)
Adaptable models: 3-8 copter, airplane, helicopter, car, boat
1 x Flight controller
1 x Power module (2-12S)
1 x Buzzer
1 x I2C transfer board
1 x Status LED
1 x 4GB MicroSD card
1 x Connection cables, adhesive tape, Type-C cable and user manual
Builders who want a full flight controller kit with a power module for many vehicle types.
An HC32F4A0PITB.
10.
16.5 g for the controller alone.
Yes, a 2-12S power module.
3-8 copters, airplanes, helicopters, cars and boats.
| Brand | Radiolink |
|---|---|
| Dimensions | 39.7 x 39.7 x 13 mm |
| MCU / Processor | HC32F4A0PITB |
| Weight | 16.500000 g |
| Selling unit | PCS |
