1 / 4Standard checkout available. Verified maker dispatch.
The Holybro PM06 V2 70A power module is a reliable power management solution for drones and UAVs that use 2S to 14S LiPo batteries. It delivers a clean, regulated 5.2V output to the flight controller and provides analogue measurements of battery voltage and current consumption through the included 6-pin JST-GH cable.
The module integrates power distribution for up to four ESCs and comes pre-assembled with an XT60 connector, 12AWG wires and a capacitor.
The PCB has a continuous current rating of 70A and a burst rating of 120A (under 60 seconds).
Wide input voltage: 2S to 14S.
Monitoring: real-time current consumption and battery voltage.
Current ratings: 70A continuous and 120A burst (under 60 seconds).
Integrated power distribution: for four ESCs.
5.2V output: 3A maximum for the flight controller.
Compact and light: 35 x 35 x 5mm and 24g.
Pre-assembled: XT60, 12AWG wires and capacitor.
A power module sits between the flight battery and the rest of the aircraft. It does two jobs: a built-in regulator (a BEC) converts the battery voltage to a clean 5V-class supply for the flight controller, and a current and voltage sensor reports how much power the aircraft is drawing. The flight controller uses the readings for battery-level warnings, failsafe decisions and flight logs.
For the readings to be trustworthy, the flight controller's battery monitor needs to be set up for the module. Enter the correct voltage and current scaling values, and compare the reported voltage with a multimeter at the battery to calibrate it. A wrong scale factor can make a battery look fuller or emptier than it really is.
Do not use the regulator to power servos or other high-current devices unless the manual says it can, because a heavy load can pull the supply down and reset the flight controller. Keep the module cool and make sure that the solder joints and connectors are secure, because this part carries the full current of the aircraft.
Quadcopters with four ESCs on a compact frame
Pixhawk-style flight controllers with analogue monitor
2S to 14S multirotor builds
Replacing separate PDB and power module
Battery monitoring and failsafe
The specification list gives an input of 2S to 14S, an output of DC 5.2V at up to 3A, a PCB continuous current rating of 70A, a burst rating of 120A (under 60 seconds), dimensions of 35 x 35 x 5mm and a weight of 24g.
The package contains the PM06 power module and a JST GHR 6-pin 1.25mm pitch cable.
Input voltage: 2S-14S
Output: DC 5.2V, 3A max
Continuous current: 70A
Burst current: 120A (under 60 seconds)
ESC outputs: four
Dimensions: 35 x 35 x 5mm
Weight: 24g
Pre-assembled: XT60, 12AWG wires, capacitor
1 x PM06 power module
1 x JST GHR 6-pin 1.25mm pitch cable
Quadcopter builders who want a power module and four-ESC distribution board in one 35 x 35mm unit.
2S to 14S.
Four.
70A continuous and 120A burst.
5.2V at up to 3A.
35 x 35 x 5mm.
The PM06 module and a JST GHR 6-pin cable.
| Brand | Holybro |
|---|---|
| Connector | XT60 |
| Dimensions | 35 x 35 x 5 mm |
| Input Voltage | 2S-14S |
| Output Voltage | 5.2V, 3A max |
| PCB Burst Current | 120.000000 A |
| PCB Continuous Current | 70.000000 A |
| Weight | 24.000000 g |
| Selling unit | PCS |
