1 / 5Sold out · Ask us about restocking
Not available to order right now.
The HGLRC SPECTER F460 is a high-performance stack for FPV racing drones that combines a flight controller with a 4-in-1 ESC. The page describes an exceptionally steady MPU6000 gyroscope and an F405 primary control chip with up to four serial connections for faster operation.
The ESC uses an FD6288 driver with ON3109 MOS. Other features include socket connections with no welding required, an immersion gold design, 16 MB blackbox recording and an onboard current meter module with real-time data display (printed as a galvanometer module). At the time of the check the page showed the item as sold out.
MPU6000 gyroscope: described as exceptionally steady.
F405 flight control chip: with up to four serial connections.
FD6288 driver with ON3109 MOS: in the 4-in-1 ESC.
Socket connections: no welding required.
Support for BEC 9V/2A and 5V/2.5A: as printed.
16 MB blackbox: flight data recording.
A flight controller is the brain of a multirotor or fixed-wing aircraft. It reads the gyroscope, and where fitted the accelerometer, barometer and compass, and runs a control loop that compares what the aircraft is doing with what the pilot asks for. It then sends new speed commands to the motors through the ESCs or servos many times each second. A faster processor and a better gyro allow a higher loop rate and a more locked-in feel.
Wiring and firmware decide what the board can do. The number of UARTs limits how many receivers, GPS units, telemetry radios and video systems you can connect, the PWM or motor outputs limit how many motors and servos it can drive, and the input voltage range must suit your battery and power module. Before you buy, check that the firmware you want to run supports the board and that its mounting pattern fits your frame.
Set up carefully. Flash a firmware that is listed as supported, configure the receiver protocol, set the motor order and direction, calibrate the accelerometer and, for larger aircraft, the compass, and always test with the propellers removed first. Keep the board isolated from vibration with soft mounts where the design calls for them, and never power it with a supply that is outside the rated input voltage.
Keep the aircraft safe. Confirm your failsafe settings and arming switch before the first flight, keep a backup of your configuration, and update firmware only when you have a reason to. A flight controller is a safety-critical part, so use the wiring diagram from the maker and avoid guesswork with power connections.
FPV racing
Freestyle drones
Socket-connected builds
Blackbox tuning
30.5 mm stack frames
The input voltage is 2-6S LiPo (7.4V to 22.8V) and the mounting hole spacing is 30.5 x 30.5 mm (M3). Supported protocols are DShot600, DShot300, DShot150, Oneshot125, Oneshot42 and Multishot.
The package is one SPECTER F460 stack and an accessory bag.
Input voltage: 2-6S LiPo (7.4V-22.8V)
MCU: F405
Gyro: MPU6000
ESC processor: FD6288 with ON3109 MOS
Blackbox: 16 MB
Mounting hole: 30.5 x 30.5 mm (M3)
Protocols: DShot600/300/150, Oneshot125/42, Multishot
BEC support: 9V/2A and 5V/2.5A (as printed)
Weight: 29 g
1 x SPECTER F460 stack
1 x Accessory bag
Racing pilots who want an F405 stack with socket connections.
An F405.
MPU6000.
2-6S LiPo.
29 g.
16 MB.
| Brand | HGLRC |
|---|---|
| Data Logging | 16MB blackbox |
| ESC Processor | FD6288 with ON3109 MOS |
| Gyro Sensor | MPU6000 |
| MCU / Processor | F405 |
| Mounting Size | 30.5x30.5mm |
| Supported Protocols | DShot600/300/150, Oneshot125/42, Multishot |
| Weight | 29.000000 g |
| Selling unit | PCS |
