Standard checkout available. Verified maker dispatch.
The Foxeer Aura LR T700 is a 5-inch ultra-lightweight quadcopter chassis built with a Deadcat geometry to keep the propellers out of view. It uses Toray T700 green carbon fibre with a silky coating and supports both analog and digital HD transmission systems.
The specification list gives a 210 mm wheelbase, M2 stack mounting holes of 20x20 mm or 25.5x25.5 mm, support for 19x19 mm micro cameras (analog and HD Vista compatible), recommended motors of 2104 to 2105.5 with a 12x12 mm mounting pattern and a frame weight of about 71 g without the TPU kit. The page did not show the item as out of stock at ₹3,759.
Toray T700 green carbon fiber: with a silky coating.
Deadcat layout: keeps propellers out of the camera view.
20x20 and 25.5x25.5 mm M2 stack holes: as listed.
19x19 mm camera cage: for micro size cameras.
TPU kit with GPS mount: motor mounts, arm guards and GPS mount.
About 71 g: excluding the TPU kit.
A drone frame is the skeleton that holds everything together: the arms carry the motors, the plates carry the flight controller, ESCs, battery and camera, and the whole structure must be stiff enough that vibration does not reach the gyro. Carbon fibre is the standard material because it is light and very rigid. The wheelbase, measured motor to motor across the diagonal, sets the size of propeller the frame can carry, and the arm thickness sets how well it survives crashes.
Match the frame to your parts. Check the motor mounting pattern, the flight controller and ESC stack hole spacing, the camera width, the video system you want to fly and the largest propeller the arms allow. TPU parts such as arm guards, antenna mounts and camera mounts are printed in a flexible plastic so they absorb impact. The battery strap and anti-slip pad keep the pack from moving under G-force.
Build carefully. Use thread-locking compound on the metal screws that are not in a plastic nut, keep the screw lengths from the hardware bag matched to the holes they belong in, and do not over-tighten screws into carbon fibre. Route motor wires away from sharp plate edges, mount the flight controller on soft grommets when the frame supports it, and check that nothing rubs a propeller before the first flight. After a crash, inspect the arms for cracks and replace any that are damaged.
Plan the balance of the build. A heavier battery moves the centre of gravity, so place it where the frame is designed to carry it, and keep the antenna, GPS and camera clear of the carbon plates where possible because carbon blocks radio signals.
Long-range FPV
5 inch Deadcat builds
HD and analog builds
GPS builds
Clean-footage flying
The recommended motors are 2104 to 2105.5 with a 12x12 mm mounting pattern. The camera cage takes 19x19 mm micro cameras.
The TPU kit has motor mounts, arm guards and an integrated GPS mount.
Wheelbase: 210 mm (5 inch)
Material: Toray T700 green carbon fiber with silky coating
Stack mounting holes: 20x20 / 25.5x25.5 mm (M2)
Camera support: 19x19 mm micro size
Recommended motors: 2104 to 2105.5, 12x12 mm pattern
Frame weight: about 71 g (excluding TPU kit)
Arms: 5 mm
1 x 5 mm arms
1 x Top, middle and bottom plates
1 x Camera mount
1 x Aluminum columns
1 x TPU arm guards and motor mounts
1 x TPU GPS and antenna mounts
1 x Screw hardware pack
1 x Battery anti-slip mat
1 x Battery strap
Long-range pilots who want a light 5 inch Deadcat frame.
210 mm.
About 71 g without the TPU kit.
19x19 mm micro cameras.
Yes, to keep the propellers out of the camera view.
| Brand | Foxeer |
|---|---|
| Arm Thickness | 5.000000 mm |
| Material | Toray T700 Carbon Fiber Sheet |
| Selling unit | PCS |
